The following is the specification of the MK1 GB3LE and is reproduced here from the website of Dave Cushman G8MZY www.dave-cushman.net

UHF FM Repeater Project
The current project of the group is a 70cm repeater using modern design practice with a better than average specification. The licence application has been made to the R.S.G.B. and the call sign GB3LE has been allocated.

The repeater is due to come into service in phase 2 of the UHF Repeater Plan, commencing APRIL 1977. The repeater is however in an advanced state of construction and it is hoped that all tests will have been completed well before this time.

The original channel allocation for this repeater was RB10, but the group made representation to the R.W.G. of the RSGB, on the grounds that this channel was the third harmonic of the local RAYNET frequency of 144.950 MHz. The current channel allocation for GB3LE is RB4 i.e. Rx-434.70 MHz. TX-433.10 MHz.

GB3LE Operation
The operation of the repeater is deliberately kept as simple as possible, primarily to promote activity, and also because the group feels that over sophistication prior to operational evaluation is unnecessary. We will of course carefully evaluate the performance and operation of the repeater, and make any changes that we feel are necessary.

Basically GB3LE receives signals on 434.7 MHz and relays them on 433.1 MHz. To obtain access, transmit on 434.70 MHz and send a tone at 1750 Hz + 50 Hz for 400 milliseconds with a minimum deviation of + 2KHz. If you have accessed successfully the repeater will send its call sign. Relayed speech is suppressed during the call sign period. Once accessed it is unnecessary to send the tone at the start of every over.

There is no "K" or 'roger bleep' fitted on GB3LE so please leave a short gap between overs. There is no short term limit to transmission time so you won't be timed out, but you are requested to keep overs to less than 2 minutes. If the repeater is in operation for a prolonged period, it will identify itself approximately every 10 minutes. Once the repeater receiver mute closes, its transmitter carrier will stay on for approximately 8 seconds. If no other station opens the mute during this period, the repeater transmitter will switch off after the F2 ident.

Remember, there may be mobile or other stations waiting to use the repeater, so please keep your overs to 2 minutes or less, and don't forget to leave a pause.

 

GB3LE SUMMARY TECHNICAL SPECIFICATION

Receiver
Frequency 434.70 MHz
Bandwidth 3db for + 15KHz
Sensitivity 0.5 µV for 20db noise quieting
Mute opens 0. 3 µV Closes 0.1 µV
Blocking Starts at 20 mV in 50 Ohm at +1.6 MHz
Intermediate Frequency 1st IF... 10.7 MHz,   2nd IF... 455 kHz
Spurious Response (Including image) -75db
AF Response -6db/octave from 300 Hz
Access Tone 1750 Hz + 50 Hz
Access Time 300 mS + l00 mS
Frequency Stability Not exceeding + 2KHz of nominal between -10° C and +50° C

Transmitter
Frequency 433.10 MHz + 1kHz
Output Power Adjustable up to 20 watts
Spurious Outputs less than 2.5 µWatts each
Noise at Receiver Frequency not greater than 0.5 x 10 -6 Watts
Modulation Deviation + 5KHz peak (F3)
Ident Deviation + 1kHz (F2) Tone at 800 Hz
Frequency Stability Not exceeding + 2KHz of nominal between -10° C and +50° C

Antenna
IMPEDANCE 50 Ohm
TYPE 6 db Collinear
Height Base of mast at proposed site 680 ft. ASL.
Location Proposed site is in ZM24J at Markfield Near Leicester.

 

BBBACK